Plastic floor wall (skirt) can decorate the wall, protect the wall and so on. Plastic floor wall can also be a decorative design of visual space. The overall installation effect is perfect. So what are the procedures for installation?

一、首先對上墻面的基層處理

First, the basic treatment of the upper wall

1.     墻面基層應當平整，干燥、堅固、無油脂、無砂粒、無起殼、無麻面、無裂紋、沒污濁等。

1. The wall base should be smooth, dry, firm, no grease, no sand, no shell, no flax, no cracks, no pollution, etc.

（墻面不可刮膩子、白水泥和白乳膠油漆等涂料，墻面找平好用水泥刷平，以增加表面強度，便于粘接）

(Wall coatings such as non-scrapable putty, white cement and white latex paint, wall leveling is best done with cement to increase surface strength and facilitate bonding)

2. 墻面在安裝前必須用打磨機或沙紙將起伏不平的墻面打磨，提高粘貼表面的平整度，打磨后的墻面必須用吸塵器將墻面完整的吸干凈，必須清除墻面的微小顆粒。

2. Before installation, the wall surface must be polished with a sandpaper or a sandpaper to improve the smoothness of the sticking surface. After polishing, the wall surface must be cleaned completely with a vacuum cleaner, and the tiny particles on the wall must be removed.

3.    內墻涂料的墻面質地松軟，直接粘貼，容易引起脫落。為了提高施工效率及節約施工成本，在不破壞原有墻面的基礎上做塑膠地板壓邊條和上墻襯板。

3. The wall texture of the interior wall paint is soft, and it is easy to fall off if it is pasted directly. In order to improve construction efficiency and save construction cost, plastic floor blank holder and wall liner are made on the basis of not destroying the original wall.

所施工墻面的陰陽角要平直，不平直的墻角會給鋪設帶來一定的難度，鋪設前，必須對不平直的陰陽角進行處理，在不平直的陰角必須用硬質三角條進行填充校正，在鋪設完畢后，陽角好安裝防撞護角加固，以提高整體的美觀。

The Yin-Yang angle of the wall to be constructed should be straight, and the uneven corner will bring some difficulties to the laying. Before laying, the uneven Yin-Yang angle must be treated. In the uneven Yin-Yang angle, the rigid triangle must be filled and corrected. After laying, the anti-collision angle should be installed to reinforce the Yang angle, so as to improve the overall beauty.

二、塑膠地板上墻的測量和裁剪

2. Measurement and Cutting of Wall on Plastic Floor

通過實地測量，以減少浪費為原則，綜合考慮美觀程度，用墨斗做長直線或者做記號準線。按需裁剪所需尺寸，發揮大經濟效益。

Through field measurement, in order to reduce waste as the principle, comprehensive consideration of the aesthetic level, using ink bucket to make long straight lines or marking alignment. Cut the required size on demand to maximize economic benefits.

操作要點：

Operating Points:

1.     切割材料必須是專人負責。

1. Cutting materials must be specially responsible.

2.     運輸搬運過程中產生的破損應當在開料前用修邊器裁去。

2. Damage caused during transportation and transportation should be cut with trimmer before raw materials.

3.     裁剪塑膠地板，必須時刻留意其方向性，避免鋪裝時拼接不上，影響美觀。

3. Cutting plastic floor, we must always pay attention to its direction, to avoid splicing when paving, affecting the beauty.

（如仿大理石、仿木紋、仿地毯、仿皮制、仿金屬、仿藝術效果要注意裁剪后能拼回原來的效果）

(For example, imitating marble, imitating wood grain, imitating carpet, imitating leather, imitating metal, imitating artistic effect, we should pay attention to the original effect after cutting.)

4.      每次切割，必須在施工現場獲得準確數據，塑膠地板有一定的回彈性，所以上墻接觸面長度是塑膠地板接觸地面的1/2（上墻長度是10cm，地面就應當留出20cm），每次開料要保留2-3cm的余量。

4. Accurate data must be obtained at the construction site for each cutting. Plastic floor has certain resilience, so the length of the upper wall contact surface is 1/2 of the length of the plastic floor contact surface (the length of the upper wall is 10 cm, the floor should be set aside 20 cm), and the remaining amount of 2-3 cm should be retained for each opening.

以上信息是我們森然塑膠地板整理發布希望對大家有所幫助我們的網站是：http://www.hghreleaserreview.com!

Above information is our Senran plastic floor finishing and publishing hope to help you with our website is: http://www.hghreleaserreview.com!